El skyport flash virtual studio

Units work into the system.The Standby and friendly name function cannot work; however, power and triggering should be possible.Please note we cannot guarantee this setup will work smoothly without issues. Misfires when using the Studio Software / App If you experience misfires, we advise setting the Auto-refresh to OFF.You’ll have better performances, but the Software/App will not scan for new units anymore.When the Auto-refresh button is ON, it will periodically read the settings on the units and scan for new units. Connect the Elinchrom Bridge to a device with Bluetooth Download the latest Elinchrom Studio App for iOS or Android and Software for macOS or Windows.Update the Elinchrom Bridge or the Elinchrom ONE/FIVE to the latest Firmware (with the Elinchrom Updater).Activate Bluetooth on your device.Switch ON the Bridge or the Elinchrom ONE.Launch the App/Software and find the connected Bridge / Elinchrom ONE/FIVE displayed in the window.The LED of the Bridge flashes in Blue.Chose the frequency channel 1 to 20, depending on which channel your flash units are set, normally to channel 1.Scan for enabled Elinchrom flash units.Start to control the units.Battery run time is about 6 to 8 hours, but the Bridge can also be used with the USB micro cable connected to your computer for charging. You can chose if you use the USB cable or the Bluetooth connection. What is Auto Off mode on the Elinchrom Bridge? The Elinchrom Bridge will automatically turn off after 120 min if no activity is detected. How to recognise units in the Studio Software / App? It is possible to click on the picture of the flash unit to send a test trigger.Once you know what unit it is, you can rename the unit with a user-friendly name. Install error on the Elinchrom Studio for macOS If you’re having an error message while installing the Elinchrom Studio on a Mac, go to:System Preferences > Security & Privacy > click, “Open Anyway” The Elinchrom Studio software on mobile devices The Elinchrom Studio App is available and compatible with iOS and Android. What is the Elinchrom Bridge module? The Elinchrom Bridge is the required link between Elinchrom units and the Elinchrom Studio Software / App to be able to control your setup. What happened with the older EL-Skyport Software? The EL-Skyport Software is not supported anymore and has been discontinued.Please refer to the Elinchrom Studio Software and the Elinchrom Bridge for the latest version. Elinchrom Studio for macOS and Windows The Elinchrom Studio software is compatible with the latest macOS and Windows operating systems. Elinchrom Studio compatibility with the Skyport USB RX The Elinchrom Studio is not compatible with the Skyport USB RX.You need the Elinchrom Bridge module to use the Elinchrom Studio Software or App. What is Auto-refresh in the Studio Software / App? When the Auto-refresh button is ON, it will periodically read the settings on the units and scan for new units.If you experience misfires, we advise setting the Auto-refresh to OFF. You’ll have better performances, but the Software/App will not

Not available with the ONE/THREE.HSS will be enabled automatically with the Transmitter Pro and compatible cameras.Note: Elinchrom units integrated into an existing Elinchrom setup with Hi-Sync and HSS units altogether work seamlessly. Can I control the ONE/THREE via smartphone or computer? Yes. You can control the ONE/THREE with the Elinchrom Studio Software and/or the iOS App. Can the ONE/THREE achieve HSS (High Speed Sync)? Yes, the ONE/THREE can enable HSS and TTL with the Transmitter Pro. Transmitter not working Check the following points:Both devices must have the same frequency channel.The transmitter and the unit must be set in the same Sync mode (Normal or Speed Mode).Change the frequency channel on the flash unit and the transmitter and test again. Is the battery of the Transmitter discharged?Are the sync cables working properly?Are the camera settings correct?Is the unit used in bright ambient light, sun, or halogen lamp directed on the photocell (the photocell may block the synchro circuit on these classical units)?Re-check the triggering in a darker room with a minimum of ambient light.Check the Transmitter with another flash unit.Avoid metal objects or walls between the flash units and the transmitter.In case a flash tube is faulty, you can hear the click sound of the flash unit but no flash; this would indicate replacing the flash tube. Dark slide on the picture If a dark slide appears on your picture, this could be a sync issue when you use too short sync speeds with DSLR cameras.You need to set the camera shutter speed at least at one value slower to maybe 1/200s or 1/160s.Read more about flash sync. EL-Skyport Receiver Universal, dead or alive? Please try the following to recover your module:Connect to the charger and wait a few minutes.An irregular flashing green light (it can be a very weak light) should appear.If you see the green light, please find the small hole above the on/off switch and press for about 10 seconds until the green light gets stronger. This will reset the module and the deeply discharged battery. Note: the charger must be connected during this process.The Universal Module’s battery should recover. If not, please contact your Elinchrom service center. EL-Skyport Speed and modeling lamp settings The EL-Skyport Speed offers the following lamp mode options:Press the + button for 3 seconds: modeling lamp is in proportional mode.Press the + button for 5 seconds: one time short the modeling lamp will switch from “Prop” to “Free” Mode and the modeling lamp will set automatically to the last “Free” value.If you wait 5 seconds after switching on the modeling lamp, the modeling lamp and the flash power can be controlled with the +/- buttons.To switch the modeling lamp off press the + button again for 3 seconds. Skyport system compatibility with cameras All cameras respecting the standard sync triggering system will work.The Hi-Sync/HSS/TTL features on the Transmitter Pro are only available for Nikon, Canon, Sony, and Fujifilm cameras (learn more). The D-Lite it and Skyport compatibility You can trigger the flash with

You Are Now Free!The Skyport Plus HS is more than just a trigger for flash units.Control & visualise power settings of your Elinchrom unitsVisual feedbackControl of all your lighting setup through a visual feedback interface with the display of power levels and modelling lamp settings.Hi-Sync technologyOnce Hi-Sync is activated, anyone can go beyond the normal X-sync of your DSLR camera. An 1/8000s shutter speed is now accessible to all, depending on the digital camera and type of flash unit.Extra distance rangeThe distance range, 200 m (656 feet) outdoors and 60 m (196 feet) indoors, will enable to work under challenging circumstances without missing an important moment. No extra receiverAny flash unit with EL-Skyport capability, either built-in or external (like Transceiver RX for Style RX, Digital RX and Ranger RX series) is compatible.What is Hi-Sync ? Hi-Sync is the open door to a complete new world of flash photography.It's time to go past the barrier of flash photography!Hi-Sync is the exclusive Elinchrom technology to go beyond the X-Sync of your DSLR camera.For Nikon, Canon, Sony, Olympus and Panasonic.It's easier than ever to setup and trigger your DSLR camera up to 1/8000s shutter speed.This allows you to do the following: Freeze motionOverpower the SunDarken backgroundUse wider aperture FeaturesEasy access to in-depth features.Take full control and expand your vision!Visual interfaceThe large LCD display features two-way control that lets you see the exact power of every light in your setup right on the transmitter. Users can control each light's power level and modelling lamp setting directly from the transmitter, which instantly shows the updated power settings.ODS (Over Drive Sync)ODS enables users to fine tune the Skyport Plus HS transmitter's trigger signal to optimize exposure at high shutter speeds while gain more light.Remote controlNot only a trigger device; it is also a remote control for up-to 10 Elinchrom flash units with built-in receivers. Control and set the flash power and the modelling lamp in 4 Groups or individually. Improved reliabilityThe EL-Skyport HS has a total of 20 frequency channels that can be used for either Normal or Speed mode. Users can instantly distinguish which sync mode they are in as the backlit display glows green for normal mode, and red for speed mode. They can also enjoy a range up to 200 m (656’) outdoors and up to 60 m (196’) indoors.CompatibilityThe EL-Skyport HS represents a seamless extension of the EL-Skyport family since it is also compatible with the three previous generations of flash units (including the EL-Skyport Transceiver RX module for Style RX, Digitial RX, and Ranger RX systems, the integrated EL-Skyport modules for D-Lite RX, BRX, ELC Pro HD and ELB series.). Future-proofThe transmitter attaches easily and securely to the hotshoe with its bayonet locking system and is powered by 2x AA batteries. It also features an integrated AF illuminator for fast focusing and a mini-USB socket for firmware updates.